DX2 Series Insert ManualFor complete installation instructions, reference the Tube Heater General Manual that accompanies this insert manual. WARNING!
10Model NumberGas Type (Select One)BTU/HStraight Length (Dim A)U-Tube Length (Dim. B)Weight (lbs.)Stainless Steel Weight (lbs.)RecommendMounting Heigh
11Tube Installation Sequence20 Foot50 Foot60 Foot70 Foot30 Foot40 FootStainless Steel Clamp on 175 - 200 MBH models (P/N: TP-220).Figure 2.4 • Tube In
WARNING!123.0 DX2 Series Operation • Sequence of Operation • Thermostat • Diagnostics3.0 OperationNote: Reference the Tube Heater General Manual for i
VALV EPSPRESSURESWITCHV133.0 Operation • DiagnosticsDX2 SeriesFigure 3.1 • Operational Indicator LightsLight 1Indicates Valve OpensLight 2 Indicates
Is the blower obstructed?Replace circuit board.Does the ignitor warm up and glow red?Is the ignitor physically damaged?Check voltage at ignitor during
NOTICEBypassing any switch is intended for testing purposes only. Do not leave switch bypassed during normal operation or the heater’s built-in safet
Does the burner ignite?164.0 Troubleshooting Guide After ignitor is warmed up, does gas valve open?Test for 120V at valve opening period (usually 30 t
17Check to make sure gas pressure is within minimum and maximum inputs, as indicated on burner rating plate. Is gas pressure OK?Were the gas lines pur
185.0 Parts • Heater Components and Parts ListChart 5.1 • Parts List *Stainless steel upgrades available. ** 6 feet total required to cover outer
Figure 5.2 • Tube & Reector Components1919B10610526A, 26B, 26E21B, 22020C, 20D8226A, 26D65I5.0 Parts • Heater Components and Parts ListDX2 Series
Contents1.0 Safety...3 Safety Labels and Locations ...
Part No. Description 20 Ft. 30 ft. 40 ft. 50 ft. 60 ft. 70 ft. 80 ft.TP-19B 4” Hanger w/ Tension Spring3 4 5 6 7 8 9TP-21B 4” Tube Clamp2 3 4* 5* 6*
DX240125NData on this label is for the model shown on this label. If your heater has been converted, this information is not accurate. Please cont
WARNING!Placement of explosive objects, ammable objects, liquids and vapors close to the heater may result in explosion, re, property damage, seriou
Model NumberMounting Angle*SideTop BelowFront BehindDX2 (20, 30, 40) - 50, 60 [N, P]0° 9 9 6 4745° 39 8 10 47with 1 side shield0° 29 8 6 47with 2 side
NOTICE62.0 Installation2.0 Installation • Gas Requirements • Electrical RequirementsElectrical Requirements • 120VAC - 60 Hz GRD, 3-wire. • 120V
WARNING!120VAC-60 Hz.SupplyNOTE: Up to 4 line voltage tube heaters can be wired to most thermostats. L1NeutralGroundHeaters on the same vent must sh
82.0 Installation • WiringDX2 SeriesBefore eld wiring this appliance - Check existing wiring; replace if necessary.Note: If any of the original wire
WBKLINE1IGNITION MODULEBRSIC1PROBEBKNEUTNEUTVALVETHGNDROWBK120VACL1BKBKGWNBKBKBK24VACBlowerIndicator LightsGas ValvePressure SwitchIgniterThermostat T
Commentaires sur ces manuels